Wheel Bearing For - Elektra Beckum BAS 315, 316, 317 Bandsaws
- High Quality UNM
- 40mm OD
- ZZ Double Shield
- Deep Groove Ball Bearings
Replacement bearing for the center of the aluminium wheels that the blade runs on.
Note: Each wheel has 2x bearings.
Sold individually.
Motor Starter Capacitor - For Elektra Beckum BAS 315, 316 & 317 Bandsaw
- Direct Replacement
- 450VAC
- 15UF or 20UF
Replacement 15UF (standard) or 20UF (older models) leaded motor starter capacitor for the Elektra Beckum BAS 315 316 Bandsaws.
If your bandsaw makes a humming sound and doesn't work when you press the start button, this part may be the cause.
This unit is on the side of the motor and connects with two wires.
Motor Starter Capacitor - For Elektra Beckum BAS 450, 500 Bandsaw
- Direct Replacement
- 425-475V
- 36UF
Replacement 36UF leaded motor starter capacitor for the Elektra Beckum BAS 450 500 Bandsaws.
If your bandsaw makes a humming sound and doesn't work when you press the start button, this part may be the cause.
This unit is on the side of the motor and connects with two wires.
Table Insert - For Elektra Beckum BAS 315, 316 & 317 Bandsaw
Replacement insert for the center of your bandsaws table.
Round plastic with slot for the blade to run through and holes to allow dusct to escape.
Table Insert - For Elektra Beckum BAS 450 & 500 Bandsaw
Replacement insert for the center of your bandsaws table.
Round plastic with slot for the blade to run through and holes to allow dusct to escape.
Tyre/Tire For - Elektra Beckum BAS 315, 316 & 317 Bandsaws
* Sold Individually - Replacement tyre for the Elektra Beckum BAS 315, 316 & 317 Bandsaws. This stretches over the aluminium wheel that the blade runs on.
The original tyres perish over time or become damaged.
These new tyres are a shrink fit and will need to be stretched onto the wheels.
Supplied With Replacement Circlip
Note: Wheel NOT Included
* Sold individually
Tyre/Tire For - Elektra Beckum BAS 250 Benchtop Bandsaws
Replacement tyre for the Elektra Beckum BAS 250 benchtop bandsaws. This stretches over the aluminium wheel that the blade runs on.
The original tyres perish over time or become damaged.
These new tyres are a shrink fit and will need to be stretched onto the wheels.
Supplied With Replacement Circlip
Note: Wheel NOT Included
* Sold individually
Drive Belt For - Elektra Beckum BAS 315, 316, 317 Bandsaw
- Replaces Factory Original
- Belt Runs From Motor To Bottom Wheel
- Supplied With Replacement Circlip
High quality poly v drive belt to replace the original belt running from the motor to the bottom wheel on Elektra Beckum 314, 315, 316 models.
Instructions: Take the tension off and remove the blade. Using a pair of circlip pliers remove the circlip on the bottom wheel. There is nothing else holding the wheel in place, so it should simply slide off the shaft. Slacken the motor only which will remove tension from the belt. Replace the belt and retension by sliding the motor back into place. Do not over tension. Replace wheel, circlip and blade.
Belt Tension Pulley - Elektra Beckum BAS 315, 316, 317 Bandsaw
- Replaces Factory Original
- Includes Bearings
Tension pulley for Elektra Beckum BAS 315 and 316 Bandsaws. Machined steel housing with two high quality sealed bearings.
Instructions: Take the tension off using the hand wheel and remove the belt. Using a pair of circlip pliers remove the circlip and slide the pulley off. There is nothing else holding the pulley in place, so it should simply slide off the shaft.
Tyre/Tire For - Elektra Beckum BAS 450, 500 Bandsaws
Replacement tyre for the Elektra Beckum BAS 450 & 500 Bandsaws. This stretches over the aluminium wheel that the blade runs on.
The original tyres perish over time or become damaged.
These new tyres are a shrink fit and will need to be stretched onto the wheels.
Note: Wheel NOT Included
* Sold individually
Drive Belt For - Elektra Beckum BAS 250 Bandsaw
- Replaces Factory Original
- Belt Runs From Motor To Bottom Wheel
- Supplied With Replacement Circlip
High quality poly v drive belt to replace the original belt running from the motor to the bottom wheel on Elektra Beckum BAS 250 bandsaws.
Instructions: Take the tension off and remove the blade. Using a pair of circlip pliers remove the circlip on the bottom wheel. There is nothing else holding the wheel in place, so it should simply slide off the shaft. Slacken the motor only which will remove tension from the belt. Replace the belt and retension by sliding the motor back into place. Do not over tension. Replace wheel, circlip and blade.
Blade Guide Upgrade Kit For - Elektra Beckum BAS 315 & 316 Bandsaws
- Complete Kit
- Billet Aluminium Blocks
- Includes Drill Template & Instructions
- Includes Bearings
- Increase Depth Of Cut By 18mm
*Out Of Stock *
Next Batch Due May/June
For updates - please select 'Notify Me When Available'
Upgrade your upper and lower cast blade guides with this fully adjustable, universal 6x bearing, billet aluminium system.
This complete 6x bearing kit replaces the upper and lower blade guides with billet blocks. Hex screws on the back of each block and sliders on each bearing allows full and fine adjustment. This stronger, easier to adjust system comes complete with bearings.
By fitting this kit your machine will also gain almost 3/4inch depth of cut (18mm) as the upper guide is shorter in height.
This kit also contains a free aluminium section rail (*New wider rail may not fit older 315 models.)
Includes two page colour fitting instructions.
More Images Here
Note: Slight modifications may be required on some models to fit the lower guide and new rail (instructions and drill template included)
-
*
New Replacement Motor For - Elektra Beckum BAS 315, 316, 317 Bandsaw
- Brand New
- Direct Replacement
- 800W/1HP Output
- 230V
Brand new direct replacement motor for your Elektra Beckum BAS 315, 316, 317 bandsaw.
Measurement between bolt holes: 70mm approx
Main Collar width: 80mm approx
More Images Here
Technical Specifications:
Motor 230V - 800W(P1) / 1HP
50Hz - 550W(P2)
4.0A - Cont. Rtg.
TEFV - 1400 min-1
REPLACING POWER SUPPLY CABLE
Replacement of the power supply cable should only be done by a qualified electrician.